Go to main content

Search Welders Net

Weld Symbols Chart: How to Read a Welding Symbol

By First published

A welding symbol is a short code on a drawing: an arrow, a reference line and a tail, with a weld symbol above or below the line. Click any symbol below to see its name, meaning and which side of the joint it describes, then build your own symbol to see how it reads. Drawings are original, written from the AWS A2.4 convention.

Weld symbol chart

Choose a symbol to read it. Without JavaScript every symbol is listed below in full.

Fillet weld

Fillet weld symbol on the arrow side1/44
Arrow side (below the line)
Fillet weld symbol on the other side1/44
Other side (above the line)
Meaning
A weld of roughly triangular cross-section that joins two surfaces meeting at an angle.
How it is drawn
A right triangle. The upright leg is always on the left. The leg size goes to the left of the symbol and the length to the right.
Typical use
T-joints, lap joints and corner joints.
Example
A 1/4 in. fillet, 4 in. long. Sources: 3, 4.

Square groove weld

Square groove weld symbol on the arrow side
Arrow side (below the line)
Square groove weld symbol on the other side
Other side (above the line)
Meaning
A butt weld between edges that are left square, with a root opening set by the drawing.
How it is drawn
Two short parallel vertical lines. The root opening is written inside the symbol.
Typical use
Butt joints in thinner material.
Example
A square-groove butt weld. Sources: 3.

V groove weld

V groove weld symbol on the arrow side
Arrow side (below the line)
V groove weld symbol on the other side
Other side (above the line)
Meaning
A butt weld where both edges are bevelled so the joint forms a V.
How it is drawn
A V with its point on the reference line. The groove angle sits above or below the symbol, the root opening inside it.
Typical use
Butt joints in plate.
Example
A V-groove butt weld. Sources: 3.

Bevel groove weld

Bevel groove weld symbol on the arrow side
Arrow side (below the line)
Bevel groove weld symbol on the other side
Other side (above the line)
Meaning
A groove where only one of the two members is bevelled.
How it is drawn
A vertical leg on the left and a slanted leg on the right. The arrow is bent to point at the member that gets the bevel.
Typical use
T-joints and corner joints in plate.
Example
A bevel-groove weld. Sources: 3, 4.

U groove weld

U groove weld symbol on the arrow side
Arrow side (below the line)
U groove weld symbol on the other side
Other side (above the line)
Meaning
A butt weld where both edges are machined to a rounded, U-shaped groove.
How it is drawn
A U sitting on the reference line, with the base of the U touching the line.
Typical use
Thick plate, to cut the amount of filler metal needed.
Example
A U-groove butt weld. Sources: 3.

J groove weld

J groove weld symbol on the arrow side
Arrow side (below the line)
J groove weld symbol on the other side
Other side (above the line)
Meaning
A groove where one member has a J-shaped (curved) preparation and the other is square.
How it is drawn
A vertical leg on the left and a curved leg on the right. The arrow is bent to point at the prepared member.
Typical use
T-joints and corner joints in thick plate.
Example
A J-groove weld. Sources: 3, 4.

Plug or slot weld

Plug or slot weld symbol on the arrow side1/2
Arrow side (below the line)
Plug or slot weld symbol on the other side1/2
Other side (above the line)
Meaning
A weld that fills a hole or slot in one member to join it to the member beneath.
How it is drawn
An open rectangle on the reference line. The hole size goes to the left; the spacing, if any, to the right.
Typical use
Lap joints where an edge weld alone is not enough.
Example
A plug weld in a 1/2 in. hole. Sources: 3.

Spot weld

Spot weld symbol on the arrow side
Arrow side (below the line)
Spot weld symbol on the other side
Other side (above the line)
Meaning
A weld made at a single spot between overlapping members, by resistance or by arc through one sheet.
How it is drawn
A small circle centred on the reference line side.
Typical use
Sheet-metal lap joints.
Example
A spot weld. Sources: 3.

Seam weld

Seam weld symbol on the arrow side
Arrow side (below the line)
Seam weld symbol on the other side
Other side (above the line)
Meaning
A continuous weld between overlapping members, made as one seam rather than separate spots.
How it is drawn
A circle with a horizontal line through it.
Typical use
Sheet-metal lap joints that must be sealed.
Example
A seam weld. Sources: 3.

Back or backing weld

Back or backing weld symbol on the arrow side
Arrow side (below the line)
Back or backing weld symbol on the other side
Other side (above the line)
Meaning
A weld laid on the reverse (root) side of a groove weld, or the backing material under it. The drawing notes say which.
How it is drawn
A half circle (an arch) on the reference line, on the side of the joint where the back weld goes.
Typical use
Full-penetration groove welds made from both sides.
Example
A back or backing weld. Sources: 3.

Build a symbol

Choose the parts

How it reads

Fillet weld on the arrow side, 1/4 in. size, 4 in. long.1/44
Your symbol (updates as you choose)

Parts of a welding symbol

A welding symbol: arrow side fillet weld, 1/4 inch size, 4 inches long, field weld flag, tail note GMAWGMAW1/44
Reference line with the arrow at the left and a tail at the right. Fillet weld on the arrow side, 1/4 in. size, 4 in. long, field weld, GMAW noted in the tail.

Where things go

  • Arrow side. Information about the arrow side of the joint goes below the reference line. (source 1)
  • Other side. Information about the other side of the joint goes above the reference line. (source 1)
  • Order along the line. Size, weld symbol, length and spacing read in that order from left to right. (source 3)

Supplementary symbols

Weld all around
A small circle where the arrow meets the reference line. The weld continues all the way around the joint. Sources: 2, 5.
Field weld
A solid flag where the arrow meets the reference line, flying toward the tail. Make this weld on site, not in the shop. Sources: 2, 5.
Contour
A short straight line (flush), an outward arc (convex) or an inward arc (concave) drawn beside the weld symbol. The finished face of the weld is flat, domed or hollowed. Sources: 2.
Tail
A fork at the far end of the reference line. Holds the process, specification or other notes. Leave it off when nothing needs saying. Sources: 3.

What this chart does not cover (unconfirmed)

  • Finishing letters (C chip, G grind, H hammer, M machine, P peen, R roll) added to a contour mark: we did not open a source for the letters, so check A2.4.
  • Flare-V and flare-bevel groove symbols, melt-through, surfacing, edge and scarf symbols: not drawn here; see A2.4.

The drawings are original and simplified. They follow the written convention, are not traced from AWS figures and may differ in proportion from the standard. AWS A2.4, Standard Symbols for Welding, Brazing, and Nondestructive Examination, is the authority; sources were read on 2026-11-14.

Questions we get

What is the difference between the arrow side and the other side?

The arrow points to one side of the joint, and that is the arrow side. Per AWS A2.4:2020 (clause 6.1, as quoted by AWS), information about the arrow side goes below the reference line and information about the other side goes above it.

Which way does the fillet weld symbol face?

Symbols with an upright leg, including the fillet and the bevel and J grooves, always have that leg on the left, according to a note reproduced from AWS A2.4. The leg size is written to the left of the symbol.

What does the circle at the corner of the symbol mean?

A circle where the arrow meets the reference line is the weld-all-around symbol: the weld continues around the whole joint.

What does the flag mean?

A solid flag where the arrow meets the reference line is the field weld symbol. It points toward the tail and tells the welder to make that weld on site, not in the shop (US Navy Steelworker manual).

Where do size, length and spacing go?

Along the reference line, in the order size, weld symbol, length and spacing, reading left to right (Indiana DOT welding-symbol appendix summarizing the AWS layout). For example 1/4 on the left and 4-10 on the right means a 1/4 in. fillet, 4 in. long, every 10 in.

Is this chart a replacement for AWS A2.4?

No. AWS A2.4 is the standard and it is not free. This page paraphrases the common conventions with original drawings and cites sources we could open. Check A2.4 itself before reading or writing a symbol that matters.

Where we got this

  1. AWS Inspection Trends, "How to Correctly Use Welding Symbols for Slotted Hollow Structural Steel Members" (quotes AWS A2.4:2020, Clause 6.1) (aws.org) Accessed 2026-11-14.
  2. US Navy, Steelworker training manual, Chapter 7 welding symbols (field weld flag, weld-all-around, contour symbols) (media.defense.gov) Accessed 2026-11-14.
  3. Indiana DOT, Appendix C: welding symbols (standard location of elements; basic weld symbols; arrow points to the grooved member) (in.gov) Accessed 2026-11-14.
  4. US Nuclear Regulatory Commission, reproduction of AWS A2.4 notes (perpendicular leg on the left) (nrc.gov) Accessed 2026-11-14. Quotes AWS A2.4:2007.
  5. North Carolina DOT, Field Welding Procedures Manual, 5.7.3 and 5.8 (weld-all-around and field weld symbols) (connect.ncdot.gov) Accessed 2026-11-14.
  6. OSHA, 29 CFR 1910.252: Welding, cutting, and brazing, general requirements (fire prevention (a), eye protection (b), ventilation (c)) (osha.gov) Accessed 2026-11-14.
  7. NIOSH (CDC), "Welding Fumes and Manganese" (cdc.gov) Accessed 2026-11-14.
  8. NIOSH, Criteria for a Recommended Standard: Welding, Brazing, and Thermal Cutting, Publication 88-110 (cdc.gov) Accessed 2026-11-14.
  9. AWS, ANSI Z49.1 Safety in Welding, Cutting, and Allied Processes (AWS Safety and Health Committee recommends following it and the manufacturer's Safety Data Sheets) (pubs.aws.org) Accessed 2026-11-14. Listing is the 2012 edition; use the current edition from AWS.

Keep reading