Welding Symbols Explained: How to Read AWS Weld Symbols
A welding symbol is a standardized drawing shorthand, defined by AWS A2.4, that tells a welder where a weld goes, what type it is, how big it is, and how it should be made. You read it around a horizontal reference line: the arrow points to the joint, the weld symbol sits above or below the line, and the tail carries the process or notes.
From the guide: Types of Welding Processes Explained: MIG, TIG, Stick, Flux-Core and More
A welding symbol is the shorthand a drawing uses to tell a welder what weld to make. If you can read it, you know where the weld goes, which type to use, how large it must be, and who has to do it. This page walks through the standard system, part by part. It sits alongside our overview of the main types of welding processes, because the process named in a symbol’s tail only makes sense once you know what each process does.
Welding symbols look cryptic at first. They are not. Every symbol is built from the same few pieces in fixed positions, and once you know the positions, you can decode most drawings in under a minute.
What Is a Welding Symbol?
A welding symbol is a standardized graphic that specifies a weld on an engineering drawing. In the United States, the standard is ANSI/AWS A2.4, Standard Symbols for Welding, Brazing, and Nondestructive Examination. The American Welding Society (AWS) describes it as a method of specifying welding, brazing, and nondestructive examination information by means of symbols, with detailed examples of how to construct and interpret them.
The goal is simple. A designer cannot draw every weld to scale, and long written notes clutter a drawing. A symbol packs the same information into a small, predictable shape that a welder, fabricator, and inspector all read the same way.
Two terms are easy to mix up:
- Weld symbol: the small graphic that shows the type of weld, such as a fillet or a groove.
- Welding symbol: the whole assembly, which includes the reference line, arrow, weld symbol, dimensions, and any extras.
AWS has published A2.4 in several editions, including 2012 and 2020. Use the edition named in your contract documents, and treat this page as a study aid, not a replacement for the standard.
What Are the Parts of a Welding Symbol?
The basic welding symbol is built around a reference line and an arrow. AWS lists the other parts as the tail, the basic weld symbol, dimensions and other data, finish symbols, specification, process or other references, and supplementary symbols.
Here is what each part does:
- Reference line. A horizontal line. Everything else is placed relative to it, so you read the symbol from this line outward.
- Arrow. A line that runs from the reference line to the joint. It tells you which joint, and which side of the joint, the symbol applies to.
- Basic weld symbol. The graphic for the weld type, placed above or below the reference line.
- Dimensions. Size, length, and spacing numbers placed in fixed positions around the weld symbol.
- Supplementary symbols. Extra marks at the arrow junction or on the weld symbol, such as weld-all-around and field weld.
- Finish symbols. Notes about how the weld surface is to be finished.
- Tail. A fork at the end opposite the arrow that holds the process, specification, or other reference. A2.4 allows the tail to be omitted when no reference is used.
A good habit is to read in the same order every time: arrow first (where), then the side of the line (which side), then the weld symbol (what type), then the numbers (how big), and finally the tail (how and by what procedure).
What Does Arrow Side and Other Side Mean?
Arrow side and other side tell you which face of the joint gets the weld. Information for the arrow side goes below the reference line, and information for the other side goes above it, according to the A2.4 provisions reproduced in the NCDOT Field Welding Procedures Manual.
The arrow side is simply the side the arrow touches. For fillet, groove, and edge welds, A2.4 says the arrow contacts the outer surface of one of the joint members, and that side is the arrow side. The opposite side is the other side.
So you have three cases:
- Symbol below the line: weld on the arrow side only.
- Symbol above the line: weld on the other side only.
- Symbol on both sides of the line: weld on both sides of the joint.
This is where most beginners make mistakes. The symbol sits above or below the line on the drawing, but the weld itself goes on the real joint. If you flip the drawing in your head, you flip the weld. Always put your finger on the arrow tip, find the joint face it touches, and decide the side from there.
For bevel and J-groove welds, the symbol also has to say which piece is prepared. A2.4 has special rules for where the arrow points on these joints, so check the standard when you see one.
How Do You Read a Fillet Weld Symbol?
A fillet weld symbol is a right triangle on the reference line. The number to its left is the fillet size, and a number to its right is the length. A hyphenated number after the length gives the pitch for intermittent welds, according to Projectmaterials’ summary of A2.4 practice.
Walk through it:
- Triangle below the line: fillet weld on the arrow side.
- Triangle above the line: fillet weld on the other side.
- Number left of the triangle: the fillet size, typically the leg size, in inches or millimeters.
- Number right of the triangle: the weld length.
- Length-pitch pair: a hyphenated pair such as 50-100 means 50 mm welds spaced 100 mm center to center.
For example, a symbol reading 1/4 on the left and a triangle below the line calls for a 1/4-inch fillet on the arrow side. If the symbol also carries 2-6 on the right, the weld is made in 2-inch segments spaced 6 inches center to center. If you see only a triangle and no numbers on a continuous weld, the weld runs the full length of the joint between changes in direction.
If no size is shown at all, do not guess. Projectmaterials advises the fabricator to determine the minimum size under the governing code, such as AWS D1.1 or the ASME piping codes, and to verify it against the project specification. In practice, you ask the engineer or the welding supervisor.
Fillet welds are most common on T-joints, lap joints, and corner joints. Our guide to welding joint types and positions shows which joints use them.
How Do You Read a Groove Weld Symbol?
A groove weld symbol shows the shape of the edge preparation that the joint needs before welding. Different symbols stand for different shapes, such as square, V, bevel, U, and J. Miller Electric describes square, V, J, and U groove edge preparations for joints where penetration or rigidity matters.
The groove symbol sits on the reference line the same way a fillet symbol does:
- Below the line: the groove is on the arrow side.
- Above the line: the groove is on the other side.
- Both sides: the joint is prepared and welded from both faces, as in a double-V joint.
Groove symbols carry more dimensions than fillet symbols. Depending on the weld, a symbol can include the groove (bevel) angle, the root opening, and the depth of preparation, all placed in set positions around the symbol. Because these numbers control penetration, never alter them without engineering approval.
Groove welds are the typical choice for butt joints, where two pieces lie in the same plane. Miller Electric lists the groove weld as the typical weld for a butt joint, and it notes that corner joints can use either a fillet or a groove weld.
What Do the Circle and Flag Mean?
The circle at the arrow bend means “weld all around,” and the flag means “field weld.” Both sit at the junction where the arrow meets the reference line.
Weld-all-around symbol
A circle at the arrow-reference line junction tells you the weld runs continuously around the joint instead of stopping at the first change of direction. A2.4 says to place the weld-all-around symbol at that junction for each operation it applies to. Use it for a pipe-to-plate connection, a boss, or any joint that wraps around a part.
Field weld symbol
A flag at the same junction tells you the weld is made in the field, not in the shop. A2.4 says the flag is placed at a right angle to the reference line and may be on either side of it. Field welds often face different conditions than shop welds, such as wind, access limits, and weld position, so the procedure may be different. If the symbol shows a field weld, check that your procedure covers outdoor work. Our stick welding guide explains why stick and self-shielded flux-core are common in the field.
A2.4 allows both marks at the same location when both apply, so you can see a circle with a flag on the same junction.
What Goes in the Tail of a Welding Symbol?
The tail holds references that do not fit anywhere else in the symbol. A2.4 lets the designer name the welding or allied process in the tail by its letter designation, such as GTAW for TIG welding or GMAW for MIG welding. The tail can also carry a welding procedure specification number, a filler metal specification, or a short note.
You will often see tail entries like these:
- A process letter designation. For example, GTAW tells you the joint is to be welded with TIG, which our TIG welding guide covers. GMAW points to MIG, covered in our MIG welding guide for beginners.
- A procedure number. This points you to a written welding procedure specification (WPS) that sets amperage, filler, preheat, and technique.
- A note. For example, a reminder to grind flush or to inspect after welding.
If the tail is absent, the symbol applies under the general notes of the drawing. Read the title block and general notes before welding, because they often say which code and which procedure govern.
Try the Interactive Weld Symbols Chart
Our weld symbols chart draws each basic symbol and shows what it means, so you can check a drawing side by side. It is a learning aid, not a replacement for the current AWS A2.4 standard cited on your drawings. If you are still deciding which process a weld calls for, the welding process picker narrows MIG, TIG, stick and flux-core by metal and thickness.
How Do Welding Symbols Relate to Joint Types?
A welding symbol only makes sense if you know the joint. A2.4 recognizes five basic joint types: butt, corner, T-, lap, and edge. Each joint tends to use certain weld symbols, such as a groove weld on a butt joint or a fillet weld on a T-joint or lap joint.
| Joint type | How the pieces meet | Typical weld (per Miller Electric) |
|---|---|---|
| Butt | Same plane, edges meeting | Groove |
| Corner | About 90 degrees, L shape | Fillet or groove |
| T-joint | One edge meets a flat face at about 90 degrees | Fillet |
| Lap | Surfaces overlap | Fillet |
| Edge | Edges parallel or nearly parallel | Groove edge preparations |
Our article on joint types and welding positions goes through each joint, plus the 1G to 6G position codes you will see on test drawings.
Worked Example: Reading One Symbol
Say you see an arrow touching the face of a vertical plate, a horizontal reference line, a triangle below the line with 3/16 to its left, and a flag at the arrow junction. Here is how you read it.
- Arrow: points to the joint between the vertical plate and the base.
- Triangle: it is a fillet weld.
- Below the line: the weld goes on the arrow side.
- 3/16 on the left: the fillet size is 3/16 inch.
- No number on the right: there is no length or pitch, so the weld is continuous.
- Flag: make the weld in the field.
The result: a continuous 3/16-inch fillet weld on the arrow side of that joint, made in the field. Notice that the answer comes from the same order every time, and nothing is guessed.
Common Mistakes When Reading Welding Symbols
Most symbol errors come from a few predictable habits:
- Reading the side backward. Below the line is the arrow side, above is the other side. Mixing these up puts the weld on the wrong face.
- Ignoring the tail. The tail may name the process or the procedure that governs the weld.
- Guessing a missing size. If no size is given, find the governing code or ask.
- Missing the all-around circle or flag. Both change how much weld you make and where you make it.
- Using an old chart. Symbols have been revised over the years, so match your chart to the edition that your drawings cite.
- Treating a symbol as a procedure. A symbol states what to weld, not how. Amperage, travel speed, and technique come from the WPS.
Where Do You Learn Welding Symbols Properly?
Most welders learn symbols through blueprint reading in a training program, then use them daily on the job. Certification tests also assume you can read them, since test drawings and procedures use the same system. Our guide to welding certifications and AWS programs explains how testing works.
For reference, keep a current copy of A2.4 or an AWS-approved chart where you work. AWS sells the standard, and the 2012 edition’s front matter is available on the AWS publications site. Before any hot work, also review the hazards in our welding safety and PPE guide, because reading the drawing correctly does not protect you from arc, fume, or fire hazards.
When a symbol is unclear, stop and ask. A quick question to the engineer or inspector costs far less than cutting out a weld.
Questions we get
What is the standard for welding symbols in the United States?
The standard is ANSI/AWS A2.4, Standard Symbols for Welding, Brazing, and Nondestructive Examination, published by the American Welding Society. It sets out how weld information is written on drawings so every welder, fabricator, and inspector reads the same thing. AWS has published the 2012 edition and a 2020 edition. Always use the edition that your contract documents or drawings name.
What do the arrow side and other side mean on a welding symbol?
The arrow side is the side of the joint the arrow touches. The other side is the opposite side of the joint. A weld symbol drawn below the reference line applies to the arrow side, and one drawn above the line applies to the other side. Symbols on both sides of the line mean welds on both sides of the joint.
What does a circle at the arrow bend on a welding symbol mean?
A circle at the junction of the arrow and the reference line is the weld-all-around symbol. It tells the welder the weld continues around the full joint, instead of stopping at the first change of direction. A2.4 places the weld-all-around symbol at that junction for each operation it applies to. If you are unsure how far it extends, ask the engineer before welding.
What does the flag on a welding symbol mean?
A flag at the junction of the arrow and the reference line is the field weld symbol. It means the weld is made in the field, at the job site, instead of in the shop. A2.4 says the flag sits at a right angle to the reference line, on either side of it.
What does the tail of a welding symbol tell you?
The tail carries references that do not fit elsewhere in the symbol. A2.4 allows the welding process, named by its letter designation such as GTAW, to be placed in the tail. The tail also commonly holds a procedure or specification reference or a note. It can be left off when no reference is needed, so a symbol with no tail is normal.
How do you read a fillet weld size on a welding symbol?
The number to the left of the triangle is the fillet size, usually the leg size, in inches or millimeters. A number to the right is the weld length. A hyphenated pair after the triangle gives length and pitch for intermittent welds, so 2-6 would mean 2-inch welds spaced 6 inches center to center. If no size is shown, check the governing code and project specification.
Do I need to memorize every welding symbol?
No. Learn the structure first: the reference line, arrow, side rule, size position, and tail. Then keep a current symbol chart or the A2.4 standard nearby for the less common symbols. Welders and fabricators look up unfamiliar symbols all the time. Guessing is the real mistake, because a wrong guess can mean a rejected weld or a weak joint, so ask the engineer or inspector when a symbol is unclear.
Where we got this
- AWS A2.4:2012 — Standard Symbols for Welding, Brazing, and Nondestructive Examination (American Welding Society) (pubs.aws.org)
- AWS A2.4:2020 — Standard Symbols for Welding, Brazing, and Nondestructive Examination (AWS publications page) (pubs.aws.org)
- AWS WHC1.08 — Symbols for Joining and Inspection (AWS publications page) (pubs.aws.org)
- NCDOT Field Welding Procedures Manual, Appendix C (reproduces AWS A2.4 clauses) (connect.ncdot.gov)
- Fillet Weld Symbol Explained — Projectmaterials (blog.projectmaterials.com)
- A Guide to the 5 Basic Types of Weld Joints — Miller Electric (millerwelds.com)
Keep reading
- Types of Welding Processes Explained: MIG, TIG, Stick, Flux-Core and More
Learn the 4 main types of welding—MIG, TIG, Stick, and Flux-Core—how each works, compatible metals, and how to pick the right process.
- Flux-Core Welding (FCAW) Guide: Self-Shielded vs Gas-Shielded
Learn flux-core welding (FCAW): self-shielded FCAW-S vs gas-shielded FCAW-G, DCEN vs DCEP polarity, knurled drive rolls, drag technique, and fume safety.
- MIG vs TIG Welding: Differences, Costs and When to Use Each
Compare MIG vs TIG welding on speed, weld appearance, skill level, gas requirements, and equipment cost to pick the right process for your project.
- MIG Welding for Beginners: Setup, Technique and Common Mistakes
Learn MIG welding (GMAW) step by step: wire sizes, C-25 gas flow rates, DCEP polarity, gun angle, travel speed, and how to fix common weld defects.
- Stick Welding (SMAW) Guide: Rods, Amperage and Technique
Learn stick welding (SMAW): how E6010, E6011, E6013, and E7018 rods work, polarity and amperage ranges, arc striking, drag technique, and safety.
- TIG Welding Guide: How GTAW Works and How to Start
Learn TIG welding (GTAW) step by step: DCEN vs AC polarity, argon flow, tungsten prep, filler technique, and safety rules.